CORC

在结果中检索

CORC

浏览/检索结果: 共29条，第1-10条 帮助

已选(0)清除 条数/页：   排序方式：
Temperature and shear rate distributions of gas‐assisted injection molded polypropylene and the application in forecast of cooling time 期刊论文
Journal of Applied Polymer Science, 2019, 卷号: Vol.136 No.16
作者:  Yu‐Chuan Zhang;  You Shi;  Lei Hu;  Bin Yang;  Ming Cao
收藏  |  浏览/下载：11/0  |  提交时间：2019/04/24
Foaming Mechanism of Polypropylene in Gas-Assisted Microcellular Injection Molding 期刊论文
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH, 2018, 卷号: 57, 期号: 13, 页码: 4710-4720
作者:  Hou, Junji;  Zhao, Guoqun;  Zhang, Lei;  Dong, Guiwei;  Wang, Guilong
收藏  |  浏览/下载：6/0  |  提交时间：2019/12/11
A novel gas-assisted microcellular injection molding method for preparing lightweight foams with superior surface appearance and enhanced mechanical performance 期刊论文
MATERIALS & DESIGN, 2017, 卷号: 127, 页码: 115-125
作者:  Hou, Junji;  Zhao, Guoqun;  Wang, Guilong;  Dong, Guiwei;  Xu, Jiaju
收藏  |  浏览/下载：10/0  |  提交时间：2019/12/11
Formation of various crystalline structures in a polypropylene/polycarbonate in situ microfibrillar blend during the melt second flow 期刊论文
PHYSICAL CHEMISTRY CHEMICAL PHYSICS, 2016, 卷号: 18, 期号: 20, 页码: 14030—14039
作者:  Xia, XC;  Yang, W;  He, S;  Xie, DD;  Zhang, RY
收藏  |  浏览/下载：23/0  |  提交时间：2016/09/12
Extension of the orientation region of high density polyethylene molded by gas-assisted injection molding: control of the thermal field 期刊论文
Polymer International, 2014, 卷号: Vol.63 No.12, 页码: 1997-2007
作者:  Xiao-Chao Xia;  Quan-Ping Zhang;  Long Wang;  Shan He;  Jian-Ming Feng
收藏  |  浏览/下载：4/0  |  提交时间：2019/03/01
Tailoring the crystalline morphologies and mechanical properties of high-density polyethylene parts by a change in the fluid flow pattern under gas-assisted injection molding 期刊论文
Journal of Applied Polymer Science, 2014, 卷号: Vol.131 No.11
作者:  Quanping Zhang;  Long Wang;  Xiaochao Xia;  Jianmin Feng;  Xiaorong Fu
收藏  |  浏览/下载：3/0  |  提交时间：2019/03/01
Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文
2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China
Zi K.; Chen L.
收藏  |  浏览/下载：13/0  |  提交时间：2013/03/25
With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.  
Crystallization behavior and molecular orientation of high density polyethylene parts prepared by gas-assisted injection molding 期刊论文
Polymer International, 2012, 卷号: Vol.61 No.4, 页码: 622-630
作者:  Zhang,K;  Wang,L;  Yang,B;  Yang,MB;  Yin,B
收藏  |  浏览/下载：2/0  |  提交时间：2019/04/22
Role of gas delay time on the hierarchical crystalline structure and mechanical property of HDPE molded by gas-assisted injection molding. 期刊论文
Colloid and Polymer Science, 2012, 卷号: Vol.290 No.12, 页码: 1133-1144
作者:  Zhang,K;  Yang,B;  Wang,L;  Yang,MB;  Feng,JM
收藏  |  浏览/下载：2/0  |  提交时间：2019/04/24
Crystallization behavior and molecular orientation of high density polyethylene parts prepared by gas-assisted injection molding 期刊论文
Polymer International, 2012, 卷号: Vol.61 No.4, 页码: 622-630
作者:  Nan Sun;  Bin Yang;  Long Wang;  Jian-Ming Feng;  Bo Yin
收藏  |  浏览/下载：5/0  |  提交时间：2019/03/26

©版权所有 ©2017 CSpace - Powered by CSpace