CORC

在结果中检索

CORC

浏览/检索结果: 共15条，第1-10条 帮助

限定条件    
已选(0)清除 条数/页：   排序方式：
Enhanced depressurization for Methane Recovery from Hydrate bearing Sediments by Ethylene Glycol Pre-injection 会议论文
INNOVATIVE SOLUTIONS FOR ENERGY TRANSITIONS, 2019-01-01
-
收藏  |  浏览/下载：2/0  |  提交时间：2020/01/03
Attenuation of collagen-induced arthritis by potential anti-inflammatory drug genistein in DBA/1 mice 会议论文
2016中国转化医学大会, 西安
作者:  
收藏  |  浏览/下载：29/0  |  提交时间：2017/01/15
Research on the Characteristics of Enrichment Fuel Injection Process in the Pre-Chamber of a Marine Gas Engine 会议论文
SAE 2015 International Powertrain, Fuels & Lubricants Meeting
作者:  Feng LY(冯立岩);  Du BG(杜宝国);  Tian JP(田江平)
收藏  |  浏览/下载：4/0  |  提交时间：2019/12/09
Hydrogen Angled Injection Effects on Combustion Characteristics in a Pre-Cooled Turbo Jet Model Afterburner 会议论文
ISABE, Busan,KOREA, 2013
George Ianus; Shinji Nakaya; Hideyuki Taguchi; Mitsuhiro Tsue
收藏  |  浏览/下载：11/0  |  提交时间：2013/11/29
High energy quadruple pass amplifier for high power laser preamplifier module 会议论文
5th international symposium on photoelectronic detection and imaging (ispdi) - high power lasers and applications
作者:  Peng, Yujie;  Wang, Jiangfeng;  Pan, Xue;  Lu, Xinghua;  Li, Xuechun
收藏  |  浏览/下载：8/0  |  提交时间：2016/11/28
Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文
2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China
Zi K.; Chen L.
收藏  |  浏览/下载：13/0  |  提交时间：2013/03/25
With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.  
Modeling and measurements of heat release distributions in dual-mode scramjet combustor 会议论文
18th AIAA/3AF International Space Planes and Hypersonic Systems and Technologies Conference 2012, Tours, France, SEP 24-28, 2012
作者:  Tian L(田璐);  Chen LH(陈立红);  Chen Q(陈强);  Li F(李飞);  Zhang XY(张新宇)
收藏  |  浏览/下载：20/0  |  提交时间：2014/02/24
Rotating Detonation Engine Injection Velocity Limit and Nozzle Effects on Its Propulsion Performance 会议论文
Wang, Jian-Ping; Shao, Ye-Tao
收藏  |  浏览/下载：3/0  |  提交时间：2015/11/13
Rotating detonation engine injection velocity limit and nozzle effects on its propulsion performance 会议论文
Wang, Jian-Ping; Shao, Ye-Tao
收藏  |  浏览/下载：3/0  |  提交时间：2017/12/03
The Study of the Railway Tunnel on the Area of Wall Rock Pre-injection 会议论文
1st International Conference on Civil Engineering, Architecture and Building Materials (CEABM 2011), JUN 18-20, 2011
作者:  Su, Huifeng;  Liu, Weining
收藏  |  浏览/下载：2/0  |  提交时间：2019/12/31

©版权所有 ©2017 CSpace - Powered by CSpace