蠕墨铸铁激光合金化熔覆的界面组织及性能

CORC > 力学研究所 > 中国科学院力学研究所 > 先进制造工艺力学重点实验室

	蠕墨铸铁激光合金化熔覆的界面组织及性能
	刘昊; 虞钢; 何秀丽; 李少霞; 朱天辉; 宁伟健; 郑彩云
刊名	材料热处理学报
	2015-03-25
卷号	36 期号:3 页码:171-176
关键词	蠕墨铸铁激光熔覆稀释率显微组织抗弯强度
其他题名	Microstructure and mechanical properties of NiCoCrAlY coating on compacted graphite iron by laser cladding
产权排序	中国科学院力学研究所先进制造工艺力学重点实验室;中国矿业大学机电工程学院;
中文摘要	针对铸铁激光熔覆涂层结合界面淬火硬化、裂纹倾向大的问题,提出激光合金化与激光熔覆相结合的工艺在蠕墨铸铁表面制备NiCoCrAlY合金涂层。通过光学显微镜、扫描电子显微镜、X射线衍射仪、维氏硬度计研究了激光合金化熔覆中熔覆层稀释率、组织、显微硬度的演化规律,通过三点弯曲试验考察了熔覆层的结合特性及力学性能。结果表明:激光合金化熔覆工艺方法将热影响区由马氏体组织转变为回火索氏体组织,降低了淬硬层深度,改善了熔覆层结合特性与塑性,抗弯强度提高到891MPa。断口显示,熔覆层与基体结合良好,断裂机制是脆性解理断裂与韧窝断裂混合机制。
英文摘要	Considering the problem of quench hardening and cracking at the interface of laser cladding coating on the cast iron, a method combined laser alloy and laser cladding was proposed to produce NiCoCrAlY coating on compacted graphite iron. The dilution, microstructure and microhardness of the coating were investigated by means of optical microscope, scanning electron microscopy, X-ray diffractometer, Vickers hardness tester. The bonding characteristics and mechanical properties of the layer were evaluated by three-point bending test. The results show that martensite turns to tempered sorbite in heat affected zone by the laser alloy cladding method, thus the depth of hardening layer decreases. Simultaneously, the bonding characteristics and plasticity are improved, and the bending strength is raised to 891 MPa. The fracture morphology shows a good bonding between coating and substrate, and also a combination of cleavage fracture and dimple fracture. ©, 2015, Editorial Office of Transactions of Materials and Heat Treatment. All right reserved.
收录类别	EI ; CSCD
语种	中文
CSCD记录号	CSCD:5407649
内容类型	期刊论文
源URL	[http://dspace.imech.ac.cn/handle/311007/58223]
专题	力学研究所_先进制造工艺力学重点实验室
推荐引用方式 GB/T 7714	刘昊,虞钢,何秀丽,等. 蠕墨铸铁激光合金化熔覆的界面组织及性能[J]. 材料热处理学报,2015,36(3):171-176.
APA	刘昊.,虞钢.,何秀丽.,李少霞.,朱天辉.,...&郑彩云.(2015).蠕墨铸铁激光合金化熔覆的界面组织及性能.材料热处理学报,36(3),171-176.
MLA	刘昊,et al."蠕墨铸铁激光合金化熔覆的界面组织及性能".材料热处理学报 36.3(2015):171-176.